RSS 36-I2-SD-ST Schmersal Electronic Components

Product Details

• EMC rating
  IEC 60947-3
• Interfering radiation
  IEC 61000-6-4
• Voltage, Utilisation category DC13
  24 VDC
• Voltage, Utilisation category DC12
  24 VDC
• Current leakage Ir
  0.5 mA
• Output current, (fail-safe output), maximum
  0.25 A
• Rated operating current (safety outputs)
  250 mA
• Switching frequency, approx.
  1 Hz
• Voltage type
  DC (direct current)
• Rated impulse withstand voltage Uimp
  0.8 kV
• Material temperature resistance (long-term), maximum
  +105 °C
• Length of sensor
  22 mm
• Mounting
  A screw length of 25 mm is sufficient for sensor mounting and for side mounting of the actuators. 30 mm long screws are recommended when the actuator is mounted upright and/or when the sealing discs are used.
• Current, Utilisation category DC13
  0.25 A
• Voltage drop Ud, maximum
  2 V
• Versions
  p-type
• Current, Utilisation category DC12
  0.25 A
• Required rated short-circuit current to EN 60947-5-1
  100 A
• Rated operating voltage, maximum
  26.4 VDC
• Rated operating voltage
  24 VDC −15 % / +10 %
Rated operating voltage, minimum
20.4 VDC
Degree of pollution to VDE 0100
3
No-load supply current I0
100 mA
Rated insulation voltage Ui
32 VDC
Protection rating
III
Overvoltage category
III
Restistance to shock
30 g / 11 ms
Resistance to vibrations to EN 60068-2-6
10 … 55 Hz, amplitude 1 mm
Material temperature resistance of the cable (in motion), minimum
-10 °C
Material temperature resistance of the cable (at rest), minimum
-30 °C
Storage and transport temperature, minimum
-25 °C
Storage and transport temperature, maximum
+85 °C
Ambient temperature, minimum
-25 °C
Operating current
150 mA
Ambient temperature, maximum
+70 °C
Height of sensor
25 mm
Degree of protection
IP65 to EN 60529, IP67 to EN 60529, IP69 to EN 60529
Width of sensor
106.3 mm
Note (Repeat accuracy R)
Axial offset: The long side allows for a maximum height misalignment (x) of sensor and actuator of 8 mm (e.g. mounting tolerance or due to guard door sagging). The axial misalignment (y) is max. ± 18 mm (see figure: Operating principle). Minimum clearance
Ensured switch distance OFF Sar
20 mm
Terminal Connector
Connector M12, 8-pole
Note
The cable section of the interconnecting cable must be observed! Cable length and cable section alter the voltage drop depending on the output current
Ensured switch distance ON Sao
10 mm
Repeat accuracy R R
0.5 mm
Switch distance
12 mm
Hysteresis (Switch distance), maximum
2 mm
Actuating panels
lateral
Number of LEDs
3
Number of Series-wiring of sensors
31
Number of semi-conductor outputs with signaling function
1
Number of fail-safe digital outputs
2
Integral System Diagnostics, status
Yes
Cascadable
Yes
Short-circuit recognition
Yes
Safety functions
Yes
Diagnostic output
Yes
Gross weight
250 g
Serial diagnostics
Yes
Duration of risk, maximum
200 ms
Reaction time, maximum
100 ms
Enclosure material
Plastic, glass-fibre reinforced thermoplastic, self-extinguishing
Short circuit detection
Yes
Time to readiness, maximum
2,000 ms
general information
Individual coding, multiple teaching
Installation conditions (mechanical)
not flush
Sensor topology
Sensor for series wiring
Active area
lateral
Housing construction form
Block
Coding level according to ISO 14119
High
Active principle
RFID
Standards
IEC 60947-5-3

RSS 36-I2-SD-ST Related Documents