RSS 36-SD-R-ST Schmersal Electronic Components

Product Details

• EMC rating
  IEC 60947-3
• Interfering radiation
  IEC 61000-6-4
• Current, Utilisation category DC13
  0.25 A
• Voltage, Utilisation category DC13
  24 VDC
• Voltage, Utilisation category DC12
  24 VDC
• Current, Utilisation category DC12
  0.25 A
• Current leakage Ir
  0.5 mA
• Versions
  p-type
• Rated operating current (safety outputs)
  250 mA
• Voltage drop Ud, maximum
  2 V
• Output current, (fail-safe output), maximum
  0.25 A
• Switching frequency, approx.
  1 Hz
• Operating current
  150 mA
• Required rated short-circuit current to EN 60947-5-1
  100 A
• Rated operating voltage
  24 VDC −15 % / +10 %
• Rated operating voltage, minimum
  20.4 VDC
• Rated operating voltage, maximum
  26.4 VDC
• No-load supply current I0
  100 mA
• Voltage type
  DC (direct current)
• Degree of pollution to VDE 0100
  3
Rated insulation voltage Ui
32 VDC
Overvoltage category
III
Protection rating
III
Rated impulse withstand voltage Uimp
0.8 kV
Restistance to shock
30 g / 11 ms
Resistance to vibrations to EN 60068-2-6
10 … 55 Hz, amplitude 1 mm
Material temperature resistance (long-term), maximum
+105 °C
Ambient temperature, maximum
+70 °C
Material temperature resistance of the cable (in motion), minimum
-10 °C
Storage and transport temperature, minimum
-25 °C
Material temperature resistance of the cable (at rest), minimum
-30 °C
Degree of protection
IP65 to EN 60529, IP67 to EN 60529, IP69 to EN 60529
Storage and transport temperature, maximum
+85 °C
Ambient temperature, minimum
-25 °C
Height of sensor
25 mm
Width of sensor
106.3 mm
Terminal Connector
Connector M12, 8-pole
Note
The cable section of the interconnecting cable must be observed! Cable length and cable section alter the voltage drop depending on the output current
Length of sensor
22 mm
Latching force
18 N
Ensured switch distance OFF Sar
20 mm
Switch distance
12 mm
Ensured switch distance ON Sao
10 mm
Mounting
A screw length of 25 mm is sufficient for sensor mounting and for side mounting of the actuators. 30 mm long screws are recommended when the actuator is mounted upright and/or when the sealing discs are used.
Note (Repeat accuracy R)
Axial offset: The long side allows for a maximum height misalignment (x) of sensor and actuator of 8 mm (e.g. mounting tolerance or due to guard door sagging). The axial misalignment (y) is max. ± 18 mm (see figure: Operating principle). Minimum clearance
Number of Series-wiring of sensors
31
Repeat accuracy R R
0.5 mm
Number of fail-safe digital outputs
2
Actuating panels
lateral
Hysteresis (Switch distance), maximum
2 mm
Number of semi-conductor outputs with signaling function
1
Number of LEDs
3
Integral System Diagnostics, status
Yes
Short-circuit recognition
Yes
Short circuit detection
Yes
Latching
Yes
Cascadable
Yes
Serial diagnostics
Yes
Safety functions
Yes
Duration of risk, maximum
200 ms
Reaction time, maximum
100 ms
Diagnostic output
Yes
general information
Universal coding
Housing construction form
Block
Standards
IEC 60947-5-3
Coding level according to ISO 14119
Low
Time to readiness, maximum
2,000 ms
Active principle
RFID
Active area
lateral
Sensor topology
Sensor for series wiring
Installation conditions (mechanical)
not flush
Gross weight
100 g
Enclosure material
Plastic, glass-fibre reinforced thermoplastic, self-extinguishing

RSS 36-SD-R-ST Related Documents